APACHE MICRO PERIPHERALS, INC.
APACHE V34I-M
|
Card Type |
Modem (asynchronous) |
|
Chip Set |
Rockwell ACi |
|
I/O Options |
None |
|
Maximum Data Rate |
28.8Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
Unidentified |
|
Fax Class |
Unidentified |
|
Data Modulation Protocol |
Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34 Rockwell V.FC |
|
Fax Modulation Protocol |
Unidentified |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
52998
|
USER CONFIGURABLE SETTINGS | ||
|
Setting |
Label |
Position |
|
í Factory configured - do not alter |
SW1/7 |
Unidentified |
|
í Factory configured - do not alter |
SW1/8 |
N/A |
Note: SW1/8 may not be present on all models. | ||
|
INTERRUPT SELECTION | ||||
|
Setting |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
|
í IRQ3 |
Off |
Off |
Off |
On |
|
IRQ4 |
Off |
Off |
On |
Off |
|
IRQ5 |
Off |
On |
Off |
Off |
|
IRQ7 |
On |
Off |
Off |
Off |
|
SERIAL PORT ADDRESS SELECTION | ||
|
Setting |
SW1/5 |
SW1/6 |
|
3F8h (COM1:) |
On |
On |
|
2F8h (COM2:) |
Off |
On |
|
3E8h (COM3:) |
On |
Off |
|
í 2E8h (COM4:) |
Off |
Off |
|
MISCELLANEOUS TECHNICAL NOTE |
|
Diagram not available. |
|
SUPPORTED STANDARD COMMANDS |
|
Basic AT Commands |
|
+++, ‘comma’, A/ |
|
A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
|
&C, &D, &F, &G, &K, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z |
|
Extended AT Commands |
|
\A, \B, \K, \N |
|
%C, %E, %L, %Q |
|
Special AT Commands |
|
#CID, +MS |
|
S-Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S26 |
|
S27, S29, S30, S31, S32, S33, S36, S38, S46, S48, S82, S86, S95 |
Note: See MHI documentation for complete information. Registers S39, S40, and S41 are unidentified bit-mapped registers. |
Proprietary AT Command Set
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#>;[cmds] |
|
Description: |
Dials the telephone number indicated according to any modifiers included in the string. |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Command |
Function |
|
DL |
Re-dial last number. |
|
DP |
Pulse dialing enabled. |
|
DS=n |
Dial stored telephone number n. |
|
DT |
Tone dialing enabled. |
|
DW |
Dialing resumed following dial tone detection. |
|
D, |
Dialing paused for amount of time specified in S8 register. |
|
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
|
D@ |
Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
|
D$ |
Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command. |
|
D^ |
Enables calling tone for this call. |
|
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
|
LINE SPEED | |
|
Type: |
Register |
|
Format |
AT [cmds] S37=n [cmds] |
|
Description: |
Sets the maximum allowable data exchange rate attempted during handshake process. |
|
Command |
Function |
|
í S37=0 |
Speed of last connection. |
|
S37=1 |
Maximum speed set to 300bps. |
|
S37=2 |
Maximum speed set to 300bps. |
|
S37=3 |
Maximum speed set to 300bps. |
|
S37=5 |
Maximum speed set to 1200bps. |
|
S37=6 |
Maximum speed set to 2400bps. |
|
S37=7 |
Maximum speed set to 1200/75bps. |
|
S37=8 |
Maximum speed set to 4800bps. |
|
S37=9 |
Maximum speed set to 9600bps. |
|
S37=10 |
Maximum speed set to 12Kbps. |
|
S37=11 |
Maximum speed set to 14.4Kbps. |
|
S37=12 |
Maximum speed set to 7200bps. |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays requested information about the modem. |
|
Command |
Function |
|
I0 |
Reports product identification code. |
|
I1 |
Reports ROM checksum. |
|
I2 |
Tests and reports ROM checksum. |
|
I3 |
Reports modem firmware version and interface type. |
|
I6 |
Reports data pump model and revision. |